C10100 and C10200 Oxygen-Free Copper Machined Parts

Rate: US$19.50 per kg

Oxygen-free copper turned parts are often specified by purchasing teams that need a particular UNS grade documented on the material certificate. C10100 is oxygen-free electronic copper, designated OFE. C10200 is oxygen-free copper, designated OF. The two share broad machining and handling concerns but have different grade requirements. Keep the drawing and the purchase order aligned so stock can be allocated and the specified grade can be traced to the finished batch. Examples include conductive contact bodies, stepped fittings, bored sleeves and shaped electrodes or contact blanks to drawing.

The Copper Development Association lists minimum electrical conductivity in the annealed condition of 101% IACS for C10100 and 100% IACS for C10200. These reference values describe material condition. They can inform selection alongside chemistry, the joining route and available stock. If a buyer has an oxygen limit, a particular material test report format or a specific electrical test on the finished part, include each as a separate requirement. The degree of oxygen control does not determine the cleaning condition, machining fluid residue or compatibility with the customer’s assembly process.

Choosing the drawing designation

Oxygen-free copper component examples

Engineering questions for the first article

May C10100 and C10200 be combined in one order?

An order can contain separate line items for separate approved grades. Identify each item by drawing and material designation. If both look alike after machining, use labels and lot separation so the receiving team can assign each shipment to its certificate.

What is needed for a clean assembly?

Provide the approved cleaning procedure or a measurable residue requirement, including the inspection method and packaging. Identify handling restrictions and whether the design has recesses that can trap rinse liquid. For special service include the exact process and any qualification required.

Can the material certificate prove purity of the delivered component?

A traceable certificate provides evidence about the original heat or lot against the ordered material specification. Separate requirements may apply to surface condition after machining, such as cleanliness or coating. If a verification test on the finished component is required, specify method, sampling and acceptance limits.

Should I give a conductivity value in the RFQ?

Yes, when conductivity is contractual. Include units, temperature or reference condition, test method and sampling. Identify whether it applies to incoming stock or the machined component. That distinction determines what the supplier can certify and when the inspection occurs.

An oxygen-free material review example

A procurement team has a drawing that calls for C10100 and a legacy parts list that says OF copper. The manufacturing review should obtain a controlled disposition so material is ordered under one exact designation. Put the final grade on the drawing, purchase order and sample inspection request. Confirm bar or rod form and specify the required documentation. If the drawing demands a test value for a particular component, identify whether the test refers to stock at a standard reference condition or to the finished part as shipped.

If machining is followed by brazing or another high-temperature assembly step, provide the joining cycle and any acceptance conditions that apply afterward. Changes in fit after assembly can come from thermal expansion, restraint, changes to material condition or local joining effects. Share the joining land and mating component detail. Decide whether the machining supplier is expected to qualify a sample before joining or whether the customer will evaluate the final assembly. Keep the resulting responsibilities visible in the quote.

Plan purity, surface and cleanliness as separate checks

The grade name identifies a defined material family. A material certificate documents the stock against the purchase requirement. A clean surface is a different acceptance question. Machining lubricants, cleaning agents and ordinary handling can introduce residues or particles regardless of the original material chemistry. If the parts go directly to an assembly or a controlled environment, identify acceptable cleaning chemistry, surface finish, packaging and any verification by the customer.

For a precision bored piece, consider how trapped liquid can leave a blind recess and whether the customer needs dry or individually protected parts. Define maximum storage time, approved bag type or handling rules only when the application requires them. A detailed handling note can make sample results more representative of delivered material. Share whether parts will be rinsed again, joined or plated after delivery, since that sequence affects the condition that should be maintained through shipment.

Compare OFE and OF at the point of design

A buyer may use the higher minimum annealed conductivity value listed for C10100 as one design input. The difference does not translate directly into the same percentage improvement for a finished electrical assembly. Compare the copper path geometry, the stock condition and the contact interfaces. When the required test is an assembly measurement, establish where the voltage is sensed and how temperature and contact force are controlled. That test can capture effects that the grade certificate does not address.

A substitute grade may be appropriate only after the customer reviews both specifications and any equipment qualification or joining requirements. For repeat work, define what evidence is needed before a grade change can be considered. If both grades are approved as alternatives, use separate line items or a written approved-alternate instruction so material and inspection remain traceable. Conex Screws can review each grade and source stock form against the submitted drawings.

Reference values and applications

The Copper Development Association data sheets identify C10100 as oxygen-free electronic copper and C10200 as oxygen-free copper. Consult the specification for the required product form when comparing chemistry and test limits. For an electrode-style body or thermal contact blank, provide the operating surfaces, finish and any downstream forming or joining operations. Treat the geometry shown on this page as illustrative and use the controlled drawing for part acceptance.

How to prepare a drawing for quotation

Send a dimensioned PDF for acceptance and a STEP model for geometry review when available. Identify the current revision on both files. The PDF should distinguish basic, reference and toleranced dimensions, specify units and define precedence when the model and drawing disagree. Share the assembly context if the finished part seats against an insulator, mates with another copper piece or passes through an enclosure. The most valuable information is usually a section through the working axis and a note identifying the features that govern acceptance at receiving.

Mark the expected order quantity, lot size and annual demand separately. Production tooling, inspection and stock planning depend on how the demand is released. A batch of samples can qualify geometry before the full release. If the drawing changes between a sample and production order, state whether the earlier inspection report still applies and list the features affected by the change. Include any quality clauses that carry over to later releases.

Choose the stock specification and condition

A copper grade is a material designation. It does not specify all of the attributes of the starting stock. State the form, temper, material specification and revision required by the contract. Where the drawing cites ASTM B187/B187M for copper rod, bar or shapes, confirm that the grade and stock form are covered by the selected edition and scope. If stock is approved to a different standard, request engineering disposition before material is ordered. Separately identify the requirements for the finished component, including dimensional checks, coating and packaging.

A material test report is most useful when the receiving team can map it to the parts in a container. If traceability is contractual, define whether it must be maintained by heat, manufacturing lot or individual piece, and how identification will be applied. A bag or carton label can protect working surfaces from marking. A permanent stamp needs an approved location away from mating faces, thin walls and tight diameters.

Set up the turning sequence around the working interface

Turned features that share an axis may benefit from production in one setup. A long bore, slot or radial hole can still require an additional operation. Establish which relationships drive the setup before the machining plan is frozen. If a part must transfer to another chuck or a separate fixture, identify the gripping zone and the surface that re-establishes the location. Check whether a previously finished section must be protected against fixture marks.

A part drawing can leave the machining sequence to the supplier while preserving requirements for the result. For qualification, ask the supplier to explain how the operation sequence protects critical faces and how it will respond when tools wear or stock changes. Where sequence is contractual because of an approved special process, put that requirement on the purchase order and identify the conditions under which a change needs customer approval.

Specify bore geometry and tool access

On a blind hole, distinguish total drilled depth from the depth of full cylindrical diameter. If the hole contains a thread, specify full-form thread depth separately from the depth of drill point and thread runout. A counterbore or spotface should have its own dimension from the reference face. Deep narrow passages need sufficient access for measurement as well as for machining. If the application accepts the natural drill point, that allowance can help simplify inspection and production.

For a through bore, give the edge requirement at both ends. A raised burr on the exit face can prevent the part from seating and skew an assembly. If a radial passage intersects the axial bore, establish where the edges may be broken and which intersection surfaces must remain clear. Inspection may combine measurement of the passage with a visual or functional check for blocked flow or snagging, depending on the application.

Use thread callouts a buyer and inspector can verify

Use the thread series, nominal size, pitch and class from the drawing. Unified inch callouts can refer to ASME B1.1 as applicable. A metric M-profile callout uses a metric diameter and pitch and its own tolerance designation. State left-hand thread explicitly when required. For an unusual thread, supply the mating drawing or master and the acceptance method. A drawing that shows only nominal diameter may leave incompatible threads looking interchangeable to a buyer.

Define usable engagement, the clearance at the end and the entry edge. On a blind tapped part, specify how much full-form thread is needed ahead of the runout. On an external stud-like feature, verify that a relief groove does not remove a length needed for engagement. Standard thread gauges check the aspects of the thread covered by their design. Where an installed shoulder or a mating member with its own runout limits travel, add a functional fit check to the inspection plan.

Compare turned surfaces, finish and edge treatment

The surface roughness requirement should identify the parameter, units and working area. When traces can run in more than one direction, specify the direction relevant to the function and the method if it is important for repeatability. Compare the desired finish with what the actual bearing surface or bore can accommodate. A small annular contact pad may leave limited space for an instrument trace, so agree the method before production.

Define where burrs are unacceptable and where edge rounding is constrained. A blanket edge break may be inappropriate on small grooves or edges that establish a working length. Show these as exceptions and identify safe handling edges where a normal chamfer is acceptable. Agree whether small surface marks are cosmetic or restricted by a functional requirement. A photographic limit sample can help clarify a finish specification when visual acceptance matters.

Plan coating around the finished part

Tin, silver and nickel can serve different functions. Specify the coating and any underlayer, thickness and areas to cover on the drawing. Call out surfaces that need masking, any limits on buildup or bridging, and areas used for rack contact if a witness mark matters. Report material and coating requirements separately so the ordering team can distinguish the base copper from the final surface. When the intended process is still being selected, describe the application and ask for an engineering review.

In a simple concentric bore with a uniform deposit on both opposing walls, a coating of thickness t on each wall reduces the diameter by approximately 2t. A corresponding outside diameter increases by about 2t. This geometric estimate assumes uniform coverage and simple cylindrical surfaces. A deep blind hole can plate unevenly, and threads require separate treatment of flank geometry and gauge fit. Verify the finished fit using the inspection method agreed for the drawing.

Agree how critical dimensions will be measured

The inspector needs the same functional datums as the design and assembly teams. Specify what establishes the axis, the face from which axial distances are measured and any feature that clocks a slot or hole. A datum setup should support the part without distorting it. For short or slender features, identify a practical checking method before committing to a tight dimensional tolerance. A dimension that can be machined reliably still needs a method that can distinguish conforming parts.

External diameters can be measured at selected planes, while bores may require plug gauges, internal measuring instruments or coordinate measurements. A go gauge confirms an acceptance condition within its design. It does not report the full bore profile. If taper, ovality, position or axial variation matters, put that geometric requirement on the drawing and agree how to check it. Document the inspection condition when temperature, measuring force or fixturing can change the readings.

First article and ongoing inspection

A first article is most useful when it comes from the intended production material and process route. Ask for a marked-up drawing with numbered characteristics and a report showing actual values for the agreed dimensional features. Give a separate row to any functional test, material verification or coating acceptance criterion. Review the lot certificate and finished inspection together so the identified sample can be tied to its stock and operation history.

Agree sampling and records before production. Identify any features subject to complete inspection, any dimensions to record at process intervals and the method for addressing a suspect batch. If process capability is requested, define the study conditions and the minimum data set. A first article shows an inspected sample at a point in time. Ongoing records and change control show whether the agreed process continues to deliver the same features during repeat orders.

Receiving and handling of machined copper parts

Decide how parts are cleaned after machining and after any coating. Bores, slots, blind recesses and intersecting holes can retain chips or processing fluid. Give a cleanliness test or an acceptance sample when the allowable condition is important. Define whether the supplier may use corrosion protection or whether the component will go directly into a customer cleaning, soldering or assembly step. Incompatible protective products can create additional preparation work at receiving.

Protect dimensions that are easy to mark or distort. Separate sharp projections from thin walls and keep the working faces from rubbing against one another. Discuss trays, dividers, individual sleeves or simple bulk packaging in light of the size, surface condition and handling route. Identify the lot, drawing revision, order number and quantity on the outer label when requested. Where the parts are supplied in groups for a matched assembly, give each group a distinct identifier.

Common RFQ questions

Can Conex Screws quote from a sample?

A physical sample can help identify the machining route, mating conditions and finish. Supply a drawing or approve a controlled drawing before production. Surface measurements on the sample may include wear, distortion or coating, so identify the accepted nominal values and state whether a replacement part must mate with legacy hardware.

Can I request both metric and inch information?

Yes. Use one unit system as the controlling dimension set and mark the other as reference where appropriate. An exact unit conversion can produce a precision that the original tolerance did not intend. Keep the thread family in its native designation. If the product goes into a mixed-unit assembly, share the mating drawing with the enquiry.

How are tolerances and lead time confirmed?

Review is based on grade, part geometry, tolerances, inspection, lot size and the stock or tooling needed for the order. Highlight the dimensions tied to assembly or electrical performance. Conex Screws can then review measurable acceptance methods, production sequence and lead time with the buyer at quotation.

How does the per-kilogram rate relate to ordering?

The listed rate for this product family is US$19.50 per kilogram. Send the drawing and requested quantity for a written quote that identifies the order basis, finish, inspection and shipping terms. If your purchasing system orders individual pieces, request the agreed piece-weight basis and price presentation for the quotation.

Can I specify a material grade different from the examples?

State the UNS designation, specification and temper and provide the target application. Quote review can check grade and stock availability, cutting access and inspection. Procurement should approve the exact designation against the drawing before any material is released.

Which checks apply before and after plating?

Use before-coating checks where they control machining or establish a baseline. Set finished-part acceptance against the agreed drawing and functional gauges. Where access is limited, agree coating measurement locations and test frequency at quote stage. Provide an approved mate for assembly-sensitive interfaces when useful.

What should a quote package include?

Provide the product drawing, revision, part quantity, target delivery, material grade and temper, critical tolerances, finish, packaging and any required reports. Include the mating drawing or assembly section if available. Attach any first article forms and identify requirements that have to be agreed before materials are procured.

Turn an assembly requirement into an inspection characteristic

Start with a sentence describing the risk. A part that stops short at assembly, rocks under a clamp or loses engagement during handling needs a different check in each case. Identify the feature in the drawing section that controls the outcome. Write its acceptance as a measurement with a datum or as a test with a controlled mating condition. Avoid a note that relies only on interpretation, such as asking for a good fit, when the requirement can be described in a drawing or test plan.

Create a short list of characteristics that govern release. Review them with the receiving team so the supplier knows which actual values and documents to include. A first article can document the relationship between related features, and ongoing checks can focus on the measurements likely to change during production. If a tolerance is changed in the drawing, record which master sample or gauge revision applies. When the fit depends on a downstream operation, agree whether the receiving inspection verifies an intermediate condition or the finished assembly.

Manufacturing and purchasing checklist

Before ordering, confirm that the drawing names the component and clearly identifies the part revision. Verify that the quotation records the same material and the same delivery condition. Ask for an approved sample or dimensional report if the geometry is new, if a new stock size must be sourced or if the same part number was previously ordered with a different finish. Include an approved deviation on the order when engineering has accepted an exception. Identify the point at which approval expires if the deviation applies only to samples.

Set the information required for future reorders. Preserve the drawing number, revision, material requirement and the inspection or packing conditions that define the part. Where samples use a process different from the intended production route, agree what evidence the production process needs before release. Where a surface has multiple requirements, identify their order of precedence and the areas to which they apply. This gives purchasing a repeatable order description and gives the incoming inspector a set of clear checks.

Define the finish and limits for visual acceptance

A finished machined surface may have normal turning marks visible under directional lighting. When appearance affects assembly or end customer acceptance, state the lighting, viewing area and permissible marks, or reference approved samples. On a concealed body, machining marks outside the working area may matter only where they create a burr or change the dimension. On a mating diameter or face, the same marks can affect seating or friction. Set the acceptance area on the drawing and identify any surfaces where contact from packing material is restricted.

Agree how witness marks are handled. A rack contact can leave a small mark after plating, and a fixture can mark a part during transfer. Restrict marks on the functional zone and establish any agreed acceptable areas before the process is approved. Keep the visual limits separate from quantitative checks for dimensions, roughness and coating thickness. When a part is intended to be further machined, specify which surfaces remain on the completed assembly and which are left as extra stock.

Material, thread and product references

• Copper Development Association C10100 data
• Copper Development Association C10200 data
• ASTM copper rod, bar and shapes specification
• ASME Unified inch screw thread standard

Send your drawing to Conex Screws

For a quotation, provide your drawing revision, material designation, finish, order quantity and any inspection documents. Include the mating geometry where fit matters. Conex Screws will review the manufacturing and acceptance requirements with your engineering or purchasing team.

Email your drawing for a quote at sales@conexscrews.com

Explore all Copper Screw Machine Parts and CNC Turned Components